两种功能化纳米金粒子固酶电极的催化性能

以合成的4-巯基苯甲酸功能化纳米金粒子和聚乙烯基吡啶包覆纳米金粒子分别作为固酶载体,制备了2种新型固酶电极,在此基础上组装了2种酶燃料电池。采用电化学方法结合紫外可见分光光度法、透射电镜技术等手段研究了固酶载体的形貌,酶-载体间相互作用对电极表面固定酶分子的光谱学性质,酶-电极间直接电子迁移能力和催化底物反应性能的影响,进一步评估和比较了两种酶燃料电池的能量输出性能。实验结果表明：4-巯基苯甲酸功能化纳米金粒子固酶基电极可以实现酶-电极间的直接电子迁移而且对葡萄糖和氧气具有良好的催化性能(催化反应起始电位分别为-0.03和0.96 V,底物转化频率分别是1.3和0.5 s^-1),其催化性能的重现性、长期使用性能、酸碱耐受性和热稳定性良好,随着自组装固酶层数的增加,催化性能随之增强直至达到极限催化电流;电池性能测试结果表明4-巯基苯甲酸功能化纳米金粒子固酶基燃料电池的开路电压为0.88 V,最大输出能量密度：864.0 μW·cm^-2,长期使用性能优异(储存3 周后仍可达到最佳能量输出的80%以上)。     

活化硅胶表面Fe~(3+)的担载及其对甲醛的催化氧化

硅胶颗粒经过400℃高温活化后与四氯化硅在无水四氢呋喃溶剂中反应制得氯化硅胶。氯化硅胶再经乙酰胺修饰,制备得到表面含羰基和氨基的硅胶修饰体。此组装体具有良好的配位能力,能够与Fe3+进行配位,从而得到表面催化活性点均匀分布的负载型催化剂。该催化剂对甲醛催化氧化具有良好的催化性能,最高催化效率高达91.3%。     

负载型钌催化剂催化对苯醌制对苯二酚的研究

采用浸渍法制备了负载型高分散纳米Ru催化剂,利用X射线衍射、X射线光电子能谱、透射电子显微镜、N2吸附-脱附实验对催化剂进行了表征,结果显示,Ru以高分散金属态存在,其平均粒径在5nm左右。考察了不同酸碱介质、催化剂与底物物质的量的比、反应温度、H2压力和反应时间对对苯二酚收率的影响。结果表明,以盐酸为反应介质,以5%Ru/AC为催化剂,nRu/AC∶n对苯醌=1∶100,反应温度30℃,H2压力3.0MPa,反应时间30min,对苯二酚的收率可达97.5%。     

环烷酸对油水界面膜流变性质的影响研究

研究了环烷酸对油水界面膜界面张力、弹性模量、损耗模量以及界面膜破裂速率常数的影响,同时对环烷酸与沥青质之间的相互作用进行了测定。结果表明,环烷酸使得原油油水界面张力下降;弹性模量随着环烷酸加量以及振荡频率的增加都分别逐渐增大,并且最终都趋于平衡;在任何振荡频率值时,损耗模量都随着环烷酸加量先增大后减小;当环烷酸加量增加时,界面膜破裂速率常数降低。环烷酸与沥青质之间存在相互作用,随着环烷酸加量的增加,其对沥青质界面膜弹性模量的影响与对原油界面膜弹性模量的影响相似,表明环烷酸主要是通过与沥青质相互作用而促进乳状液稳定性的。     

Synthesis and performances for treating oily wastewater produced from polymer flooding of new demulsifiers based on polyoxyalkylated N,N‐dimethylethanolamine

Usually, oily wastewater produced from polymer flooding (OWPF) was treated by cationic polymer in oilfield. In this paper, six block copolymers of ethylene oxide and propylene oxide were prepared by using N,N‐dimethylethanolamine (DMEA) as the acceptor (DMEA‐mnp and DMEA‐mnpq, n:m:p:q represented the weight ratio of different blocks). Most of DMEA products could perform well for treating OWPF, especially DMEA1231. Their performances were mainly affected by temperature. The reason of increasing oil removal performance of DMEA1231 with temperature was the decrease of interfacial dilational modulus (ε) with increasing temperature. When temperature raised up to 55°C, the ε of DMEA1231 had the minimum (1.5 l mN/m). Therefore, the OiW had the minimum (90 mg/l). Because DMEA1231 had the best performance, its flocculation kinetics was studied systemically. The results showed that the optimum condition for DMEA1231 was as follows: dosage was 300 mg/l, temperature was 55°C, stirring speed was 200 rpm and stirring time was 5 min. At last, the offshore oil field test was carried out to check the DMEA1231 performance. The result showed that at the optimum condition, DMEA1231 could perform as well as the cationic polymer. The most important thing was that flocs of DMEA1231 were not viscous and floated on the surface of the water. The results obtained by this paper provide a good choice for the treatment of OWPF in offshore oilfield to avoid the formation of viscous flocs. Copyright © 2014 John Wiley & Sons, Ltd.     

Improving the impact property and heat‐resistance of PLA/PC blends through coupling molecular chains at the interface

The influences of both the molecular structure and the melt viscosity differences between Poly(lactic acid) (PLA) and polycarbonate (PC) on the interpenetration of molecular chains at the interface were investigated by comparing the dynamic mechanical properties and morphologies of the as‐prepared PLA/PC solution‐casting blends with those of their corresponding annealed (180°C, 8 h) samples or PLA/PC melt blends. Additionally, two chain extenders containing epoxy groups (ADR and TGDDM) were used to improve the interfacial strength. Subsequently, the interpenetration of PLA and PC molecular chains at the interface was also surveyed. Finally, the effects of the morphology formed by after adding ADR or TGDDM on the impact property, and heat resistance were discussed. The results showed that there was no interpenetration of molecular chains at the interface in PLA/PC melt blends because of the serious hindrance of the molecular structure and the melt viscosity differences. Although the interfacial strength achieved significant increase after adding ADR or TGDDM, the increase of the interfacial strength should be caused by the connection of ADR or TGDDM molecules with PLA and PC molecules at the interface through chemical bonds rather than the entanglements of PLA and PC molecular chains because of no interpenetration of PLA and PC molecular chains at the interface. Thus, the morphology formed after adding ADR or TGDDM is still the type of complete phase separation, which may be the most suitable morphology for achieving high impact and heat resistance PLA/PC blends because these two properties strongly depend on the crystallinity of PLA phase. Copyright © 2015 John Wiley & Sons, Ltd.     

High‐Resolution Single‐Molecule Fluorescence Imaging of Zeolite Aggregates within Real‐Life Fluid Catalytic Cracking Particles

Fluid catalytic cracking (FCC) is a major process in oil refineries to produce gasoline and base chemicals from crude oil fractions. The spatial distribution and acidity of zeolite aggregates embedded within the 50–150 μm‐sized FCC spheres heavily influence their catalytic performance. Single‐molecule fluorescence‐based imaging methods, namely nanometer accuracy by stochastic chemical reactions (NASCA) and super‐resolution optical fluctuation imaging (SOFI) were used to study the catalytic activity of sub‐micrometer zeolite ZSM‐5 domains within real‐life FCC catalyst particles. The formation of fluorescent product molecules taking place at Brønsted acid sites was monitored with single turnover sensitivity and high spatiotemporal resolution, providing detailed insight in dispersion and catalytic activity of zeolite ZSM‐5 aggregates. The results point towards substantial differences in turnover frequencies between the zeolite aggregates, revealing significant intraparticle heterogeneities in Brønsted reactivity.     

Synthesis,Crystal Structure and Catalytic Properties of a 2D Cobalt(Ⅱ) Coordination Polymer Based on Mixed Ligands

A new Co(II) metal-organic coordination polymer based on flexible bis(imidazole) and aromatic dicarboxylate co-ligands, namely [Co(bix)(nph)]n(H2nph = 3-nitrophthalic acid, bix = 1,4-bis(imidazole-1-ylmethyl)benzene), has been hydrothermally synthesized and characterized by elemental analyses, TG, IR spectroscopy and single-crystal X-ray diffraction. It crystallizes in the triclinic space group P1 with a = 9.3767(14), b = 10.1451(15), c = 12.1488(17), α = 102.6450(10), β = 108.856(2), γ = 98.807(2)°, V = 1035.3(3)3, Z = 2, C22H17 Co N5O6, Mr = 506.34, Dc = 1.624 g/cm3, μ = 0.882 mm-1 and F(000) = 518. In the complex, the nph2- ligands connect neighbouring cobalt atoms to form binuclear [Co(nph)]2 subunits, which are linked by pairs of bix ligands to form a 2D honeycomb-like(6,3) network. In addition, the compound is further extended into a 3D supramolecular architecture by π···π stacking interactions. Moreover, the luminescence and catalytic properties of the complex are investigated.     

氧化钛负载脱硝催化剂的碱中毒过程：氧化钒的保留和氧化钨的牺牲

V2O5-WO3/TiO2催化剂目前已广泛用于电厂和工业锅炉燃烧废气脱硝,但燃烧原料煤及石油中含有的杂质元素碱金属与碱土金属元素可吸附在催化剂上,不仅会减少催化剂酸性位的数量,还会与催化活性元素结合生成惰性物种,导致催化剂失活。因此,已有许多有关钒钨钛催化剂碱中毒的研究,从催化剂的氧化还原能力、酸性位损失及表面孔结构等方面进行了讨论。但这些研究大多集中在碱中毒对活性组分V2O5的影响及中毒催化剂的活性变化,很少涉及催化剂中WO3的作用,也缺乏有关不同活性元素与钾盐反应的实验证据。本文采用过量浸渍法制备了不同钒和钨含量的钒钨钛催化剂,研究了氯化钾对其氨法选择性催化还原(NH3-SCR)活性的失活效应。利用感应耦合等离子体、N2吸附、拉曼光谱、H2程序升温还原、NH3吸附红外光谱和NH3氧化活性等手段对新鲜和中毒催化剂的性质进行了表征,特别探讨了V2O5和WO3对催化剂抗碱中毒能力的贡献。
　　催化剂活性测试结果表明, V2O5含量越高,活性温度窗口越宽,而且含有WO3的三元催化剂活性高于V2O5/TiO2二元催化剂。催化剂的BET比表面积和孔结构取决于TiO2载体,随活性组分配比变化不大,说明催化剂物理结构性质并非影响活性的主要因素。原位红外光谱及H2程序升温还原测试结果表明,随V2O5含量提高,催化剂表面Br?nsted酸性位数量及氧化还原能力提高。作为反应的主要活性物种, V2O5在碱中毒处理后变成惰性的偏钒酸钾KVO3,使催化剂中Br?nsted酸性位减少,热稳定性下降,并削弱了催化剂的氧化还原能力,因此低钒含量的催化剂容易严重中毒失活。在高钒负载量(3%)时,部分V2O5在碱中毒后得以保留,从而使催化剂保持了一定的脱硝催化活性。
　　另外, WO3能给催化剂表面提供热稳定的酸性位,虽然WO3自身的氧化还原能力差,但其能改善V2O5的分散性,从而提高V2O5-WO3/TiO2催化剂的活性。除此之外, WO3在催化剂碱中毒过程中还能扮演牺牲剂,与钾反应生成钨酸钾(K2WO4),即在V2O5与钾离子结合形成KVO3的同时,部分WO3也会与钾反应形成K2WO4,可以使三元催化剂保留更多的活性V物种。因此,在所研究的催化剂中,高钒负载量的V2O5-WO3/TiO2催化剂表现出最好的抗碱中毒能力。
　　活性影响因素分析表明,对于新鲜催化剂,其表面吸附的NH3量足够多,催化剂活性与表面酸性相关度不大,脱硝效率主要取决于催化剂的氧化还原能力。但是,对于碱中毒处理后的催化剂,其表面吸附NH3的能力大大削弱,这时脱硝效率除了受催化剂氧化还原能力影响,在很大程度上也依赖于催化剂的表面酸性。     

SCR催化剂碱(土)金属中毒的研究进展

在选择性催化还原(SCR)烟气脱硝系统中,催化剂碱(土)金属中毒和再生受到广泛关注。本文综述了SCR脱硝催化剂碱(土)金属中毒的失活机理及基于分子水平上碱金属中毒的研究新思路,并根据催化剂的各种失活机理,有针对性地综述了提高催化剂抗碱金属中毒的途径及中毒催化剂的再生方法。